How Much Concrete Do You Need for a 16×20 Slab?
Calculate the exact ready-mix yardage, 80-lb and 60-lb bag counts, subbase gravel, and rebar reinforcement needed for a 16×20 concrete slab (320 sq ft).
Exact net volume: 3.95 yd³ (106.67 cu ft)
Standard application: Pedestrian walkways, back patios, gazebo bases, small garden sheds.
Exact net volume: 5.93 yd³ (160 cu ft)
Heavy-duty application: Garage floors, carports, RV pads, hot tub foundations, machinery shops.
How to measureSlab dimensions diagram
16×20 Slab Concrete Volume & Bag Chart
Reference table comparing exact net volume and recommended order amounts across standard residential slab thicknesses for 320 square feet:
| Slab Thickness | Recommended For | Net Cu Ft | Net Cu Yds | Order (Yds + 10%) | 80 lb Bags (+10%) | 60 lb Bags (+10%) |
|---|---|---|---|---|---|---|
| 4 Inches | Sidewalks, Patios, Light Sheds | 106.67 ft³ | 3.95 yd³ | 4.35 yd³ | 196 | 261 |
| 5 Inches Recommended | Workshops, Carports, Light Trucks | 133.33 ft³ | 4.94 yd³ | 5.43 yd³ | 245 | 326 |
| 6 Inches | Two-Car Garages, RVs, Hot Tubs | 160 ft³ | 5.93 yd³ | 6.52 yd³ | 294 | 392 |
| 8 Inches | Heavy Machinery, Farm Slabs | 213.33 ft³ | 7.9 yd³ | 8.69 yd³ | 392 | 522 |
* Bag calculations assume 0.60 cu ft per 80-lb bag and 0.45 cu ft per 60-lb bag, with a 10% safety allowance for subbase compaction and forms.
Engineering & Code Specifications for a 16×20 Slab
Guidelines aligned with American Concrete Institute standard ACI 302.1R (Guide for Concrete Floor and Slab Construction) and IRC Section R506:
Subbase & Compaction
4" to 6" compacted crushed rock subbase
Rebar & Mesh Reinforcement
#4 rebar at 18" on-center both ways elevated on dobies
Contraction & Control Joints
Cut into four equal 8×10 ft quadrants within 12–24 hours of placement
Mix Strength & Curing
Specify 3,500 to 4,000 PSI ready-mix concrete with 5% to 7% air entrainment in cold climates. Moist cure with wet burlap or spray a curing compound (ASTM C309) for a minimum of 7 days before traffic.
Project Design Notes for 16×20 (Pavilion / Outbuilding Slab)
A 16×20 slab (320 sq ft) works well for two-bay golf cart garages, timber-frame covered pavilions, or detached utility sheds. For pavilions with heavy timber corner columns, cast J-bolt anchor posts or embed galvanized post bases directly into thickened corner piers.
Estimated Cost for a 16×20 Concrete Slab
Concrete material cost delivered to your jobsite ($125 to $165 per cubic yard). Excludes wooden forms, rebar, gravel subbase, and tool rental.
Typical contractor turnkey rate ($6 to $12 per sq ft for 320 sq ft). Covers site excavation, formwork, crushed stone base, rebar grid, pour, screed, and broom finish.
Explore Other Concrete Slab Sizes
Frequently Asked Questions: 16×20 Slab
How many cubic yards of concrete do I need for a 20x16 slab at 4 inches thick?
For a 16×20 slab at 4 inches thick (320 sq ft), you need exactly 3.95 cubic yards (106.67 cubic feet) of concrete. When ordering ready-mix concrete, contractors recommend adding a 10% waste allowance for subbase irregularities and spillage, bringing your recommended order to 4.35 cubic yards. The formula is: (20 ft × 16 ft × 0.333 ft) ÷ 27 = 3.95 yd³.
How many 80 lb bags of Quikrete do I need for a 20x16 slab?
For a 4-inch thick 16×20 slab, you will need 196 eighty-pound bags of concrete (or 261 sixty-pound bags), which includes a 10% safety margin. If pouring a heavy-duty 6-inch slab, you will need 294 eighty-pound bags (or 392 sixty-pound bags). Each standard 80-lb bag yields approximately 0.60 cubic feet of mixed concrete.
Should a 20x16 slab be 4 or 6 inches thick?
Choose your slab thickness based on intended use: A 4-inch pour (4.35 yd³ with waste) is standard for pedestrian patios, walkways, and small garden sheds holding under 100 sq ft. A 5 to 6-inch pour (6.52 yd³ with waste) reinforced with #4 rebar on an aggregate subbase is strongly recommended for garage floors, carports, RV pads, hot tubs, or any application supporting vehicle axle weights per ACI 302.1R and IRC R506.
How much does a 20x16 concrete slab cost?
Ready-mix concrete delivery costs between $125 and $165 per cubic yard. For a 4-inch 16×20 slab (4.35 yd³ ordered), materials will cost approximately $544 to $718. For a 6-inch slab (6.52 yd³ ordered), ready-mix concrete runs $815 to $1076. A complete turnkey installation by a concrete contractor (including grading, forms, gravel base, rebar, pour, and finishing) typically ranges from $6.00 to $12.00 per sq ft, or $1,920 to $3,840 total for 320 sq ft.