Exact Dimension Guide 240 Sq Ft Garages & Vehicle Pads

How Much Concrete Do You Need for a 12×20 Slab?

Calculate the exact ready-mix yardage, 80-lb and 60-lb bag counts, subbase gravel, and rebar reinforcement needed for a 12×20 concrete slab (240 sq ft).

Instant Concrete Estimate — 12×20 Slab (240 sq ft)
Includes recommended 10% waste factor
4-Inch Thick Slab
3.26 Cubic Yards

Exact net volume: 2.96 yd³ (80 cu ft)

147 80 lb bags (+10%)
or
196 60 lb bags (+10%)

Standard application: Pedestrian walkways, back patios, gazebo bases, small garden sheds.

Ready-Mix Truck vs. Bagged Recommendation: Ready-mix truck delivery required (order 4.9 to 5.0 cubic yards with 10% waste for a 6" slab).

Customize Your 12×20 Slab Calculation

The calculator below is pre-configured for a 20′ × 12′ slab. Modify thickness, waste percentage, or local price per yard to calculate exact costs in real time:

Enter Dimensions

Quick Presets:

Separate dimensions with x and entries with commas. Use positive decimal dimensions.

Enter length x width in decimal feet, separated by commas. Example: 4x5, -2x3 adds 20 ft² and deducts 6 ft². Use non-overlapping sections at the same depth.

Standard residential slabs are 4 in thick

Results

Concrete Required
4.444 yd³
Standard US ready-mix order unit

Equivalent

267 × bags 60 lb Bags (raw) Exact volume only — no waste allowance
200 × bags 80 lb Bags (raw) Exact volume only — no waste allowance
294 × bags 60 lb Bags (+ 10% waste) Recommended order quantity including 10% waste allowance
220 × bags 80 lb Bags (+ 10% waste) Recommended order quantity including 10% waste allowance
120 ft³ Cubic Feet
3.398 m³ Cubic Meters
Your layout

Recommended Order:  4.89  yd³

Includes 10% waste allowance (5–15% typical for this material)

Simple rectangular slabs: 5–10% is adequate. Add 15% for complex shapes or uneven subgrade.

Estimated Cost Market Rate
$444  –  $778 per cubic yard (ready-mix)

Based on current market rates. Actual cost varies by region, supplier, and project complexity.

Enter Your Price
$
Estimated total $0.00

How to measureSlab dimensions diagram

Length Width Thickness Volume = length × width × thickness
Slab dimensions diagram
Concrete slab: length × width × thickness — enter each dimension above to calculate volume.

12×20 Slab Concrete Volume & Bag Chart

Reference table comparing exact net volume and recommended order amounts across standard residential slab thicknesses for 240 square feet:

Slab Thickness Recommended For Net Cu Ft Net Cu Yds Order (Yds + 10%) 80 lb Bags (+10%) 60 lb Bags (+10%)
4 Inches Sidewalks, Patios, Light Sheds 80 ft³ 2.96 yd³ 3.26 yd³ 147 196
5 Inches Workshops, Carports, Light Trucks 100 ft³ 3.7 yd³ 4.07 yd³ 184 245
6 Inches Recommended Two-Car Garages, RVs, Hot Tubs 120 ft³ 4.44 yd³ 4.89 yd³ 220 294
8 Inches Heavy Machinery, Farm Slabs 160 ft³ 5.93 yd³ 6.52 yd³ 294 392

* Bag calculations assume 0.60 cu ft per 80-lb bag and 0.45 cu ft per 60-lb bag, with a 10% safety allowance for subbase compaction and forms.

Engineering & Code Specifications for a 12×20 Slab

Guidelines aligned with American Concrete Institute standard ACI 302.1R (Guide for Concrete Floor and Slab Construction) and IRC Section R506:

Subbase & Compaction

6" crushed stone base compacted in two 3" lifts with plate compactor to 95% density

Rebar & Mesh Reinforcement

#4 rebar (1/2") on 16" centers tied with wire and placed on 2.5" chairs

Contraction & Control Joints

Saw-cut at 10 ft along the 20-ft length (two 12×10 ft sections)

Mix Strength & Curing

Specify 3,500 to 4,000 PSI ready-mix concrete with 5% to 7% air entrainment in cold climates. Moist cure with wet burlap or spray a curing compound (ASTM C309) for a minimum of 7 days before traffic.

Project Design Notes for 12×20 (Single-Car Garage / RV Pad)

A 12×20 slab (240 sq ft) supports full-size pickup trucks, SUVs, or single-axle travel trailers. Pour at 5" to 6" thickness using 4,000 PSI compressive strength concrete per ACI 302.1R to prevent wheel cracking under sustained vehicle curb weights.

Estimated Cost for a 12×20 Concrete Slab

DIY / Ready-Mix Delivery Only
$408 – $807

Concrete material cost delivered to your jobsite ($125 to $165 per cubic yard). Excludes wooden forms, rebar, gravel subbase, and tool rental.

Turnkey Professional Installation
$1,440 – $2,880

Typical contractor turnkey rate ($6 to $12 per sq ft for 240 sq ft). Covers site excavation, formwork, crushed stone base, rebar grid, pour, screed, and broom finish.

Explore Other Concrete Slab Sizes

Frequently Asked Questions: 12×20 Slab

How many cubic yards of concrete do I need for a 20x12 slab at 4 inches thick?

For a 12×20 slab at 4 inches thick (240 sq ft), you need exactly 2.96 cubic yards (80 cubic feet) of concrete. When ordering ready-mix concrete, contractors recommend adding a 10% waste allowance for subbase irregularities and spillage, bringing your recommended order to 3.26 cubic yards. The formula is: (20 ft × 12 ft × 0.333 ft) ÷ 27 = 2.96 yd³.

How many 80 lb bags of Quikrete do I need for a 20x12 slab?

For a 4-inch thick 12×20 slab, you will need 147 eighty-pound bags of concrete (or 196 sixty-pound bags), which includes a 10% safety margin. If pouring a heavy-duty 6-inch slab, you will need 220 eighty-pound bags (or 294 sixty-pound bags). Each standard 80-lb bag yields approximately 0.60 cubic feet of mixed concrete.

Should a 20x12 slab be 4 or 6 inches thick?

Choose your slab thickness based on intended use: A 4-inch pour (3.26 yd³ with waste) is standard for pedestrian patios, walkways, and small garden sheds holding under 100 sq ft. A 5 to 6-inch pour (4.89 yd³ with waste) reinforced with #4 rebar on an aggregate subbase is strongly recommended for garage floors, carports, RV pads, hot tubs, or any application supporting vehicle axle weights per ACI 302.1R and IRC R506.

How much does a 20x12 concrete slab cost?

Ready-mix concrete delivery costs between $125 and $165 per cubic yard. For a 4-inch 12×20 slab (3.26 yd³ ordered), materials will cost approximately $408 to $538. For a 6-inch slab (4.89 yd³ ordered), ready-mix concrete runs $611 to $807. A complete turnkey installation by a concrete contractor (including grading, forms, gravel base, rebar, pour, and finishing) typically ranges from $6.00 to $12.00 per sq ft, or $1,440 to $2,880 total for 240 sq ft.