Gravel Calculator
Estimate gravel, crushed stone, or aggregate by volume and weight for driveways, paths, and drainage. Enter the area dimensions and depth to get cubic yards, cubic feet, and tons. Most loose gravel weighs roughly 1.4 tons per cubic yard, which the calculator uses to convert volume to delivery weight.
How to measureGravel Area Diagram
How the Formula Works
Convert depth to feet
Depth (ft) = Depth (in) ÷ 12 All dimensions must share the same unit before multiplying
Calculate volume in cubic feet
Volume (ft³) = Length (ft) × Width (ft) × Depth (ft) Convert to cubic yards
Volume (yd³) = Volume (ft³) ÷ 27 There are 27 cubic feet in one cubic yard — the standard US gravel order unit
Calculate tons of gravel
Tons = Cubic Yards × Density Tonnage depends on material density, which varies by moisture and exact material type.
Common Driveway, Patio & Walkway Gravel Quantities
Estimated cubic yards and tons for standard project dimensions based on typical crushed stone density (1.4 tons per cubic yard):
| Project Size (ft) | Area (sq ft) | Depth (in) | Volume (yd³) | Weight (Tons at 1.4 t/yd³) |
|---|---|---|---|---|
| 10′ × 10′ Patio | 100 | 3" | 0.93 | 1.30 |
| 10′ × 10′ Patio | 100 | 4" | 1.23 | 1.73 |
| 10′ × 20′ Parking Pad | 200 | 3" | 1.85 | 2.59 |
| 10′ × 20′ Parking Pad | 200 | 4" | 2.47 | 3.46 |
| 12′ × 20′ Carport Base | 240 | 3" | 2.22 | 3.11 |
| 12′ × 20′ Carport Base | 240 | 4" | 2.96 | 4.15 |
| 12′ × 40′ Driveway | 480 | 3" | 4.44 | 6.22 |
| 12′ × 40′ Driveway | 480 | 4" | 5.93 | 8.30 |
| 20′ × 20′ Garage Apron | 400 | 3" | 3.70 | 5.19 |
| 20′ × 20′ Garage Apron | 400 | 4" | 4.94 | 6.91 |
Frequently Asked Questions
For a standard gravel driveway, you need 4–6 inches of depth. Enter your driveway length and width above with a 4-inch depth as a starting point. A 100 ft × 12 ft driveway at 4 inches deep requires approximately 14.8 cubic yards (about 21 tons) of gravel.
Standard gravel weighs approximately 2,800 lbs per cubic yard, which equals 1.4 US short tons. This varies by gravel type: pea gravel is slightly lighter (~1.25 tons/yd³), while crushed stone can be heavier (~1.5 tons/yd³).
Recommended depths: driveways 4–6 inches, walkways and paths 2–4 inches, decorative landscaping 2–3 inches, drainage base layers 6–12 inches. Thicker layers resist displacement and last longer but cost more.
Break the area into rectangles, run this calculator for each section, then add the results together. For circular areas, use π × r² for the area, then multiply by depth. For L-shaped areas, split into two rectangles.
Crushed stone (#57 stone) is the most popular driveway gravel — it packs well and drains effectively. Pea gravel looks attractive but shifts under traffic. Road base (crusher run) provides excellent stability for a base layer. Always use 3 layers: a 6-inch base of road base, 4 inches of #57 stone, and 2 inches of pea gravel or #10 screenings on top.
Multiply cubic yards by 1.4 to get US short tons (e.g., 10 yd³ × 1.4 = 14 tons). For metric, multiply cubic meters by 1.52 to get metric tonnes. Gravel suppliers typically sell by the ton, so this conversion is essential when ordering.
Yes — order 10–15% extra to account for compaction, uneven ground, and delivery variation. Gravel compacts roughly 20–30% after installation, so your finished layer will be shallower than the loose depth.
Gravel costs $15–$75 per cubic yard depending on type and location. Pea gravel runs $15–$30/yd³, crushed stone $20–$40/yd³, and specialty decorative gravels up to $75/yd³. Delivery typically adds $50–$150 depending on distance.
How to Use the Gravel Calculator
Whether you are building a new rural driveway, pouring a shed base, or top-dressing an existing gravel lane, this calculator provides exact cubic yards and aggregate tonnage factoring in material density and compaction:
- Enter Project Dimensions: Input your project length and width in feet or meters. For long driveways, verify accurate wheel-path widths (typically 10 to 12 feet for residential lanes).
- Specify Layer Depth: Use 2 inches for surface replenishment or top dressing, 4 inches for shed pads and standard resurfacing, or 6 to 8 inches for brand-new driveway construction over native subgrade.
- Review Tonnage & Truckloads: Review both cubic yards and tons for your chosen aggregate density. Contractors recommend ordering 10% extra to compensate for subgrade settling and mechanical compaction.
Popular Gravel Driveway & Pad Sizes (Quick Reference)
Planning a driveway, parking pad, or shed foundation with standard dimensions? Explore our exact-dimension calculation guides complete with tonnage charts, cubic yardage, dump truck counts, and depth recommendations:
Small Shed Base / Walkway Pad
Patio Base / Fire Pit Area
Storage Shed Gravel Pad
Single Car Parking Pad
RV / Boat Parking Pad
Two-Car Gravel Parking Pad
Garage / Pole Barn Subbase Pad
50-Foot Single-Lane Driveway
50-Foot Standard Gravel Driveway
100-Foot Single-Lane Driveway
100-Foot Standard Gravel Driveway
200-Foot Rural Gravel Driveway
Common Gravel Project Dimensions & Tonnage Reference Table
Reference table showing cubic yards and estimated tonnage across 12 standard project dimensions. Tonnage is calculated at 1.4 tons per cubic yard (#57 crushed stone) with a 10% compaction allowance:
| Project Size (ft) | Typical Application | Area (sq ft) | 4" Depth (Tons) | 6" Depth (Tons) | 4" Order (yd³) | 6" Order (yd³) |
|---|---|---|---|---|---|---|
| 8×10 Area | Small Shed Base / Walkway Pad | 80 | 1.5 t | 2.3 t | 1.09 yd³ | 1.63 yd³ |
| 10×10 Area | Patio Base / Fire Pit Area | 100 | 1.9 t | 2.9 t | 1.36 yd³ | 2.04 yd³ |
| 10×12 Area | Storage Shed Gravel Pad | 120 | 2.3 t | 3.4 t | 1.63 yd³ | 2.44 yd³ |
| 10×20 Area | Single Car Parking Pad | 200 | 3.8 t | 5.7 t | 2.72 yd³ | 4.07 yd³ |
| 12×20 Area | RV / Boat Parking Pad | 240 | 4.6 t | 6.8 t | 3.26 yd³ | 4.89 yd³ |
| 20×20 Area | Two-Car Gravel Parking Pad | 400 | 7.6 t | 11.4 t | 5.43 yd³ | 8.15 yd³ |
| 24×24 Area | Garage / Pole Barn Subbase Pad | 576 | 11 t | 16.4 t | 7.82 yd³ | 11.73 yd³ |
| 10×50 Area | 50-Foot Single-Lane Driveway | 500 | 9.5 t | 14.3 t | 6.79 yd³ | 10.19 yd³ |
| 12×50 Area | 50-Foot Standard Gravel Driveway | 600 | 11.4 t | 17.1 t | 8.15 yd³ | 12.22 yd³ |
| 10×100 Area | 100-Foot Single-Lane Driveway | 1000 | 19 t | 28.5 t | 13.58 yd³ | 20.37 yd³ |
| 12×100 Area | 100-Foot Standard Gravel Driveway | 1200 | 22.8 t | 34.2 t | 16.3 yd³ | 24.44 yd³ |
| 12×200 Area | 200-Foot Rural Gravel Driveway | 2400 | 45.6 t | 68.4 t | 32.59 yd³ | 48.89 yd³ |
Gravel Aggregate Types & Density Comparison
Different stone types have distinct bulk densities that affect how many tons you need per cubic yard:
- #57 Crushed Stone (1.40 tons/yd³ / ~2,800 lbs): Angular 1/2" to 1" clean crushed limestone or granite without stone dust. Ideal for drainage layers, French drains, and intermediate driveway support.
- #411 Crusher Run / Dense Grade (1.50 tons/yd³ / ~3,000 lbs): Blended mix of 3/4" crushed rock down to fine stone dust. When wetted and rolled, it forms a tight, interlocking, cement-like driving surface that resists washboarding.
- Pea Gravel (1.35 tons/yd³ / ~2,700 lbs): Smooth, rounded 3/8" river pebbles. Excellent for decorative pathways, dog runs, and playground groundcover, but too mobile for heavy vehicle parking.
- #3 & #4 Ballast Stone (1.45 tons/yd³ / ~2,900 lbs): Large 2" to 3" fractured rock used as the bottom foundation layer for driveways built over soft, clay-rich subgrade soils.