Exact Area Guide 2400 Sq Ft 200-Foot Rural Gravel Driveway

How Many Tons & Yards of Gravel for a 12×200 Area?

Calculate the exact crushed stone tonnage, cubic yardage, dump truck loads, and depth requirements for a 12×200 gravel driveway, parking pad, or shed foundation (2400 sq ft).

Instant Gravel Estimate — 12×200 Area (2400 sq ft)
Includes 10% compaction & grade allowance
6-Inch Depth (Heavy Base Layer)
68.4 Tons of Gravel

Recommended order: 48.89 yd³ (exact net: 44.44 yd³ / 1200 cu ft)

73.3 tons Crusher Run (#411)
•
66 tons Pea Gravel

Best for: Brand-new driveway installations over dirt, RV/boat pads, and heavy truck parking.

Dump Truck Delivery Guide: 3 to 4 tri-axle dump truck loads (~45.6 tons at 4", or ~68.4 tons at 6") based on standard 12–14 ton tri-axle capacities.

Customize Your 12×200 Gravel Calculation

The calculator below is pre-configured for a 200′ × 12′ area. Adjust depth, stone density, or price per ton to calculate exact requirements:

Enter Dimensions

Quick Presets:

Enter length x width in decimal feet, separated by commas. Example: 4x5, -2x3 adds 20 ft² and deducts 6 ft². Use non-overlapping sections at the same depth.

Driveways: 4–6 in. Paths: 2–4 in. Decorative: 2–3 in.

Default is 1.4 tons/yd³. Actual density varies by moisture and material type.

Results

Cubic Yards
29.63 yd³
Standard US gravel order unit
41.481 tons Tons of Gravel
800 ft³ Cubic Feet
22.653 m³ Cubic Meters
Your layout

Recommended Order:  32.59  yd³

Includes 10% waste allowance (10–15% typical for this material)

Gravel compacts and settles after spreading. Add 10–15% to reach your target finished depth.

Estimated Cost Market Rate
$444  –  $2222 per cubic yard (material only)

Based on current market rates. Actual cost varies by region, supplier, and project complexity.

Enter Your Price
$
Estimated total $0.00

How to measureGravel Area Diagram

Top view Length Width Side view Gravel Depth
Gravel Area Diagram
Measure the footprint and the depth of gravel alone. The weight estimate depends on gravel density.

12×200 Gravel Depth & Material Reference Chart

Quick reference comparing cubic yards and tonnage across common aggregate types for 2400 square feet:

Gravel Depth Application / Purpose Net Cu Yds Order (Yds + 10%) #57 Stone (1.4 t/yd³) Crusher Run (1.5 t/yd³) Pea Gravel (1.35 t/yd³)
2 Inches Light Top Dressing / Maintenance 14.81 yd³ 16.3 yd³ 22.8 tons 24.4 tons 22 tons
3 Inches Walkway, Patio, Garden Bed 22.22 yd³ 24.44 yd³ 34.2 tons 36.7 tons 33 tons
4 Inches Recommended Standard Resurfacing & Shed Pad 29.63 yd³ 32.59 yd³ 45.6 tons 48.9 tons 44 tons
6 Inches New Driveway Base / RV Pad 44.44 yd³ 48.89 yd³ 68.4 tons 73.3 tons 66 tons
8 Inches Heavy Equipment Roadbed / Subbase 59.26 yd³ 65.19 yd³ 91.3 tons 97.8 tons 88 tons

* Tonnage estimates factor in a 10% allowance for subbase compaction and track irregularities. Standard crushed stone is calculated at 2,800 lbs/yd³ (1.4 tons/yd³); crusher run/dense grade at 3,000 lbs/yd³ (1.5 tons/yd³).

The 3-Layer Gravel Driveway Engineering Rule

Laying gravel directly on top of bare topsoil inevitably causes rutting, potholes, and sinking. Professional civil roadbuilders construct gravel driveways in three structured layers:

Layer 0

Geotextile Subgrade Fabric

Roll out heavy-duty non-woven geotextile fabric (6–8 oz) over stripped subsoil. This prevents crushed rock from sinking into the subgrade while allowing groundwater to drain freely without turning stone to mud.

Layer 1

Base Layer: #3 or #4 Ballast Stone (4"–6")

Coarse, fractured 2" to 3" rock creates an interlocking structural foundation. This layer bridges soft ground, prevents wheel rutting, and provides internal void space for subsurface stormwater runoff.

Layer 2

Middle Layer: #57 Crushed Stone (2"–3")

Angular 3/4" clean crushed limestone or granite bridges the large gaps between the ballast stones. This creates a stable intermediate transition layer that will not shift under braking or steering.

Layer 3

Surface Layer: #411 Crusher Run (2")

Also known as dense grade aggregate (DGA) or road bond. Contains 3/4" crushed rock blended with stone dust. When watered and compacted with a vibratory roller, the fines bind into a hard, cement-like surface crust. Crown the center 1/2" per foot toward side ditches.

Site Preparation Notes for 12×200 (200-Foot Rural Gravel Driveway)

A 200-foot rural driveway covers 2,400 sq ft. For long country driveways, professional "tailgate spreading" by the dump truck driver saves hours of grading labor. Always install culvert pipes at ditch crossings before laying stone.

Estimated Material Cost for a 12×200 Area

4-Inch Depth (Delivered Material)
$1368 – $2508

Estimated material cost for 45.6 tons of #57 stone delivered by tri-axle dump truck ($30 to $55 per ton depending on distance from local quarry).

6-Inch Heavy Base (Delivered Material)
$2052 – $3762

Estimated material cost for 68.4 tons of structural stone delivered. If hiring a mini-excavator or skid steer operator for grading and rolling, add $600 to $1,500.

Explore Other Gravel Driveway & Pad Sizes

Frequently Asked Questions: 12×200 Gravel Area

How many tons of gravel do I need for a 200x12 area at 4 inches deep?

For a 12×200 area (2400 sq ft) at a standard 4-inch depth, you need 45.6 tons of #57 crushed stone (or 48.9 tons of dense grade crusher run). This calculation factors in a 10% allowance for subbase settling and compaction. At 4 inches, the volume equals 29.63 net cubic yards (32.59 cubic yards recommended order).

How many cubic yards of gravel is a 200x12 area?

At a 4-inch depth, a 12×200 area measures exactly 29.63 net cubic yards (order 32.59 cubic yards with 10% compaction). If installing a heavy 6-inch subbase layer, you will need 44.44 net cubic yards (order 48.89 cubic yards). The formula is: (200 ft × 12 ft × [depth in inches ÷ 12]) ÷ 27.

How many dump truck loads of gravel do I need for a 200x12 project?

A standard tri-axle dump truck carries between 12 and 14 tons of crushed gravel, while a tandem-axle truck holds 7 to 8 tons. For a 4-inch depth on a 12×200 area (45.6 tons total), you will need 3 to 4 tri-axle dump truck loads (~45.6 tons at 4", or ~68.4 tons at 6"). Ordering in full truckloads significantly lowers delivery surcharges.

How much does gravel cost for a 200x12 driveway or pad?

Crushed stone (#57 limestone or granite) generally costs $30 to $55 per ton delivered. For a 4-inch depth (45.6 tons), material will cost roughly $1368 to $2508. For a 6-inch depth (68.4 tons), budget approximately $2052 to $3762 for stone delivery.