Exact Area Guide 1000 Sq Ft 100-Foot Single-Lane Driveway

How Many Tons & Yards of Gravel for a 10×100 Area?

Calculate the exact crushed stone tonnage, cubic yardage, dump truck loads, and depth requirements for a 10×100 gravel driveway, parking pad, or shed foundation (1000 sq ft).

Instant Gravel Estimate — 10×100 Area (1000 sq ft)
Includes 10% compaction & grade allowance
6-Inch Depth (Heavy Base Layer)
28.5 Tons of Gravel

Recommended order: 20.37 yd³ (exact net: 18.52 yd³ / 500 cu ft)

30.6 tons Crusher Run (#411)
•
27.5 tons Pea Gravel

Best for: Brand-new driveway installations over dirt, RV/boat pads, and heavy truck parking.

Dump Truck Delivery Guide: 1 to 2 tri-axle dump truck loads (~19.0 tons at 4", or ~28.5 tons at 6") based on standard 12–14 ton tri-axle capacities.

Customize Your 10×100 Gravel Calculation

The calculator below is pre-configured for a 100′ × 10′ area. Adjust depth, stone density, or price per ton to calculate exact requirements:

Enter Dimensions

Quick Presets:

Enter length x width in decimal feet, separated by commas. Example: 4x5, -2x3 adds 20 ft² and deducts 6 ft². Use non-overlapping sections at the same depth.

Driveways: 4–6 in. Paths: 2–4 in. Decorative: 2–3 in.

Default is 1.4 tons/yd³. Actual density varies by moisture and material type.

Results

Cubic Yards
12.346 yd³
Standard US gravel order unit
17.284 tons Tons of Gravel
333.333 ft³ Cubic Feet
9.439 m³ Cubic Meters
Your layout

Recommended Order:  13.58  yd³

Includes 10% waste allowance (10–15% typical for this material)

Gravel compacts and settles after spreading. Add 10–15% to reach your target finished depth.

Estimated Cost Market Rate
$185  –  $926 per cubic yard (material only)

Based on current market rates. Actual cost varies by region, supplier, and project complexity.

Enter Your Price
$
Estimated total $0.00

How to measureGravel Area Diagram

Top view Length Width Side view Gravel Depth
Gravel Area Diagram
Measure the footprint and the depth of gravel alone. The weight estimate depends on gravel density.

10×100 Gravel Depth & Material Reference Chart

Quick reference comparing cubic yards and tonnage across common aggregate types for 1000 square feet:

Gravel Depth Application / Purpose Net Cu Yds Order (Yds + 10%) #57 Stone (1.4 t/yd³) Crusher Run (1.5 t/yd³) Pea Gravel (1.35 t/yd³)
2 Inches Light Top Dressing / Maintenance 6.17 yd³ 6.79 yd³ 9.5 tons 10.2 tons 9.2 tons
3 Inches Walkway, Patio, Garden Bed 9.26 yd³ 10.19 yd³ 14.3 tons 15.3 tons 13.8 tons
4 Inches Recommended Standard Resurfacing & Shed Pad 12.35 yd³ 13.58 yd³ 19 tons 20.4 tons 18.3 tons
6 Inches New Driveway Base / RV Pad 18.52 yd³ 20.37 yd³ 28.5 tons 30.6 tons 27.5 tons
8 Inches Heavy Equipment Roadbed / Subbase 24.69 yd³ 27.16 yd³ 38 tons 40.7 tons 36.7 tons

* Tonnage estimates factor in a 10% allowance for subbase compaction and track irregularities. Standard crushed stone is calculated at 2,800 lbs/yd³ (1.4 tons/yd³); crusher run/dense grade at 3,000 lbs/yd³ (1.5 tons/yd³).

The 3-Layer Gravel Driveway Engineering Rule

Laying gravel directly on top of bare topsoil inevitably causes rutting, potholes, and sinking. Professional civil roadbuilders construct gravel driveways in three structured layers:

Layer 0

Geotextile Subgrade Fabric

Roll out heavy-duty non-woven geotextile fabric (6–8 oz) over stripped subsoil. This prevents crushed rock from sinking into the subgrade while allowing groundwater to drain freely without turning stone to mud.

Layer 1

Base Layer: #3 or #4 Ballast Stone (4"–6")

Coarse, fractured 2" to 3" rock creates an interlocking structural foundation. This layer bridges soft ground, prevents wheel rutting, and provides internal void space for subsurface stormwater runoff.

Layer 2

Middle Layer: #57 Crushed Stone (2"–3")

Angular 3/4" clean crushed limestone or granite bridges the large gaps between the ballast stones. This creates a stable intermediate transition layer that will not shift under braking or steering.

Layer 3

Surface Layer: #411 Crusher Run (2")

Also known as dense grade aggregate (DGA) or road bond. Contains 3/4" crushed rock blended with stone dust. When watered and compacted with a vibratory roller, the fines bind into a hard, cement-like surface crust. Crown the center 1/2" per foot toward side ditches.

Site Preparation Notes for 10×100 (100-Foot Single-Lane Driveway)

A 100-foot rural or suburban driveway lane covers 1,000 sq ft. Ordering in full tri-axle loads (typically 12 to 14 tons per truck) maximizes material savings and minimizes hauling trip fees.

Estimated Material Cost for a 10×100 Area

4-Inch Depth (Delivered Material)
$570 – $1045

Estimated material cost for 19 tons of #57 stone delivered by tri-axle dump truck ($30 to $55 per ton depending on distance from local quarry).

6-Inch Heavy Base (Delivered Material)
$855 – $1568

Estimated material cost for 28.5 tons of structural stone delivered. If hiring a mini-excavator or skid steer operator for grading and rolling, add $600 to $1,500.

Explore Other Gravel Driveway & Pad Sizes

Frequently Asked Questions: 10×100 Gravel Area

How many tons of gravel do I need for a 100x10 area at 4 inches deep?

For a 10×100 area (1000 sq ft) at a standard 4-inch depth, you need 19 tons of #57 crushed stone (or 20.4 tons of dense grade crusher run). This calculation factors in a 10% allowance for subbase settling and compaction. At 4 inches, the volume equals 12.35 net cubic yards (13.58 cubic yards recommended order).

How many cubic yards of gravel is a 100x10 area?

At a 4-inch depth, a 10×100 area measures exactly 12.35 net cubic yards (order 13.58 cubic yards with 10% compaction). If installing a heavy 6-inch subbase layer, you will need 18.52 net cubic yards (order 20.37 cubic yards). The formula is: (100 ft × 10 ft × [depth in inches ÷ 12]) ÷ 27.

How many dump truck loads of gravel do I need for a 100x10 project?

A standard tri-axle dump truck carries between 12 and 14 tons of crushed gravel, while a tandem-axle truck holds 7 to 8 tons. For a 4-inch depth on a 10×100 area (19 tons total), you will need 1 to 2 tri-axle dump truck loads (~19.0 tons at 4", or ~28.5 tons at 6"). Ordering in full truckloads significantly lowers delivery surcharges.

How much does gravel cost for a 100x10 driveway or pad?

Crushed stone (#57 limestone or granite) generally costs $30 to $55 per ton delivered. For a 4-inch depth (19 tons), material will cost roughly $570 to $1045. For a 6-inch depth (28.5 tons), budget approximately $855 to $1568 for stone delivery.