Exact Area Guide 80 Sq Ft Small Shed Base / Walkway Pad

How Many Tons & Yards of Gravel for a 8×10 Area?

Calculate the exact crushed stone tonnage, cubic yardage, dump truck loads, and depth requirements for a 8×10 gravel driveway, parking pad, or shed foundation (80 sq ft).

Instant Gravel Estimate — 8×10 Area (80 sq ft)
Includes 10% compaction & grade allowance
6-Inch Depth (Heavy Base Layer)
2.3 Tons of Gravel

Recommended order: 1.63 yd³ (exact net: 1.48 yd³ / 40 cu ft)

2.4 tons Crusher Run (#411)
•
2.2 tons Pea Gravel

Best for: Brand-new driveway installations over dirt, RV/boat pads, and heavy truck parking.

Dump Truck Delivery Guide: 1 pickup truck bed or local landscaping trailer (under 2 tons) based on standard 12–14 ton tri-axle capacities.

Customize Your 8×10 Gravel Calculation

The calculator below is pre-configured for a 10′ × 8′ area. Adjust depth, stone density, or price per ton to calculate exact requirements:

Enter Dimensions

Quick Presets:

Enter length x width in decimal feet, separated by commas. Example: 4x5, -2x3 adds 20 ft² and deducts 6 ft². Use non-overlapping sections at the same depth.

Driveways: 4–6 in. Paths: 2–4 in. Decorative: 2–3 in.

Default is 1.4 tons/yd³. Actual density varies by moisture and material type.

Results

Cubic Yards
0.988 yd³
Standard US gravel order unit
1.383 tons Tons of Gravel
26.667 ft³ Cubic Feet
0.755 m³ Cubic Meters
Your layout

Recommended Order:  1.09  yd³

Includes 10% waste allowance (10–15% typical for this material)

Gravel compacts and settles after spreading. Add 10–15% to reach your target finished depth.

Estimated Cost Market Rate
$15  –  $74 per cubic yard (material only)

Based on current market rates. Actual cost varies by region, supplier, and project complexity.

Enter Your Price
$
Estimated total $0.00

How to measureGravel Area Diagram

Top view Length Width Side view Gravel Depth
Gravel Area Diagram
Measure the footprint and the depth of gravel alone. The weight estimate depends on gravel density.

8×10 Gravel Depth & Material Reference Chart

Quick reference comparing cubic yards and tonnage across common aggregate types for 80 square feet:

Gravel Depth Application / Purpose Net Cu Yds Order (Yds + 10%) #57 Stone (1.4 t/yd³) Crusher Run (1.5 t/yd³) Pea Gravel (1.35 t/yd³)
2 Inches Light Top Dressing / Maintenance 0.49 yd³ 0.54 yd³ 0.8 tons 0.8 tons 0.7 tons
3 Inches Walkway, Patio, Garden Bed 0.74 yd³ 0.81 yd³ 1.1 tons 1.2 tons 1.1 tons
4 Inches Recommended Standard Resurfacing & Shed Pad 0.99 yd³ 1.09 yd³ 1.5 tons 1.6 tons 1.5 tons
6 Inches New Driveway Base / RV Pad 1.48 yd³ 1.63 yd³ 2.3 tons 2.4 tons 2.2 tons
8 Inches Heavy Equipment Roadbed / Subbase 1.98 yd³ 2.17 yd³ 3 tons 3.3 tons 2.9 tons

* Tonnage estimates factor in a 10% allowance for subbase compaction and track irregularities. Standard crushed stone is calculated at 2,800 lbs/yd³ (1.4 tons/yd³); crusher run/dense grade at 3,000 lbs/yd³ (1.5 tons/yd³).

The 3-Layer Gravel Driveway Engineering Rule

Laying gravel directly on top of bare topsoil inevitably causes rutting, potholes, and sinking. Professional civil roadbuilders construct gravel driveways in three structured layers:

Layer 0

Geotextile Subgrade Fabric

Roll out heavy-duty non-woven geotextile fabric (6–8 oz) over stripped subsoil. This prevents crushed rock from sinking into the subgrade while allowing groundwater to drain freely without turning stone to mud.

Layer 1

Base Layer: #3 or #4 Ballast Stone (4"–6")

Coarse, fractured 2" to 3" rock creates an interlocking structural foundation. This layer bridges soft ground, prevents wheel rutting, and provides internal void space for subsurface stormwater runoff.

Layer 2

Middle Layer: #57 Crushed Stone (2"–3")

Angular 3/4" clean crushed limestone or granite bridges the large gaps between the ballast stones. This creates a stable intermediate transition layer that will not shift under braking or steering.

Layer 3

Surface Layer: #411 Crusher Run (2")

Also known as dense grade aggregate (DGA) or road bond. Contains 3/4" crushed rock blended with stone dust. When watered and compacted with a vibratory roller, the fines bind into a hard, cement-like surface crust. Crown the center 1/2" per foot toward side ditches.

Site Preparation Notes for 8×10 (Small Shed Base / Walkway Pad)

An 8×10 gravel pad (80 sq ft) creates a free-draining foundation for small tool sheds or garden pathways. A 4" layer of compacted crushed run (#411) over non-woven geotextile fabric prevents mud migration and keeps wooden shed runners rot-free.

Estimated Material Cost for a 8×10 Area

4-Inch Depth (Delivered Material)
$45 – $83

Estimated material cost for 1.5 tons of #57 stone delivered by tri-axle dump truck ($30 to $55 per ton depending on distance from local quarry).

6-Inch Heavy Base (Delivered Material)
$69 – $126

Estimated material cost for 2.3 tons of structural stone delivered. If hiring a mini-excavator or skid steer operator for grading and rolling, add $600 to $1,500.

Explore Other Gravel Driveway & Pad Sizes

Frequently Asked Questions: 8×10 Gravel Area

How many tons of gravel do I need for a 10x8 area at 4 inches deep?

For a 8×10 area (80 sq ft) at a standard 4-inch depth, you need 1.5 tons of #57 crushed stone (or 1.6 tons of dense grade crusher run). This calculation factors in a 10% allowance for subbase settling and compaction. At 4 inches, the volume equals 0.99 net cubic yards (1.09 cubic yards recommended order).

How many cubic yards of gravel is a 10x8 area?

At a 4-inch depth, a 8×10 area measures exactly 0.99 net cubic yards (order 1.09 cubic yards with 10% compaction). If installing a heavy 6-inch subbase layer, you will need 1.48 net cubic yards (order 1.63 cubic yards). The formula is: (10 ft × 8 ft × [depth in inches ÷ 12]) ÷ 27.

How many dump truck loads of gravel do I need for a 10x8 project?

A standard tri-axle dump truck carries between 12 and 14 tons of crushed gravel, while a tandem-axle truck holds 7 to 8 tons. For a 4-inch depth on a 8×10 area (1.5 tons total), you will need 1 pickup truck bed or local landscaping trailer (under 2 tons). Ordering in full truckloads significantly lowers delivery surcharges.

How much does gravel cost for a 10x8 driveway or pad?

Crushed stone (#57 limestone or granite) generally costs $30 to $55 per ton delivered. For a 4-inch depth (1.5 tons), material will cost roughly $45 to $83. For a 6-inch depth (2.3 tons), budget approximately $69 to $126 for stone delivery.