Exact Area Guide 400 Sq Ft Two-Car Gravel Parking Pad

How Many Tons & Yards of Gravel for a 20×20 Area?

Calculate the exact crushed stone tonnage, cubic yardage, dump truck loads, and depth requirements for a 20×20 gravel driveway, parking pad, or shed foundation (400 sq ft).

Instant Gravel Estimate — 20×20 Area (400 sq ft)
Includes 10% compaction & grade allowance
4-Inch Depth (Standard Layer)
7.6 Tons of Gravel

Recommended order: 5.43 yd³ (exact net: 4.94 yd³ / 133.33 cu ft)

8.1 tons Crusher Run (#411)
•
7.3 tons Pea Gravel

Best for: Driveway resurfacing, top-dressing existing stone, walkways, and shed pads.

Dump Truck Delivery Guide: 1 standard tri-axle dump truck load (~11.4 tons at 6") based on standard 12–14 ton tri-axle capacities.

Customize Your 20×20 Gravel Calculation

The calculator below is pre-configured for a 20′ × 20′ area. Adjust depth, stone density, or price per ton to calculate exact requirements:

Enter Dimensions

Quick Presets:

Enter length x width in decimal feet, separated by commas. Example: 4x5, -2x3 adds 20 ft² and deducts 6 ft². Use non-overlapping sections at the same depth.

Driveways: 4–6 in. Paths: 2–4 in. Decorative: 2–3 in.

Default is 1.4 tons/yd³. Actual density varies by moisture and material type.

Results

Cubic Yards
7.407 yd³
Standard US gravel order unit
10.37 tons Tons of Gravel
200 ft³ Cubic Feet
5.663 m³ Cubic Meters
Your layout

Recommended Order:  8.15  yd³

Includes 10% waste allowance (10–15% typical for this material)

Gravel compacts and settles after spreading. Add 10–15% to reach your target finished depth.

Estimated Cost Market Rate
$111  –  $556 per cubic yard (material only)

Based on current market rates. Actual cost varies by region, supplier, and project complexity.

Enter Your Price
$
Estimated total $0.00

How to measureGravel Area Diagram

Top view Length Width Side view Gravel Depth
Gravel Area Diagram
Measure the footprint and the depth of gravel alone. The weight estimate depends on gravel density.

20×20 Gravel Depth & Material Reference Chart

Quick reference comparing cubic yards and tonnage across common aggregate types for 400 square feet:

Gravel Depth Application / Purpose Net Cu Yds Order (Yds + 10%) #57 Stone (1.4 t/yd³) Crusher Run (1.5 t/yd³) Pea Gravel (1.35 t/yd³)
2 Inches Light Top Dressing / Maintenance 2.47 yd³ 2.72 yd³ 3.8 tons 4.1 tons 3.7 tons
3 Inches Walkway, Patio, Garden Bed 3.7 yd³ 4.07 yd³ 5.7 tons 6.1 tons 5.5 tons
4 Inches Standard Resurfacing & Shed Pad 4.94 yd³ 5.43 yd³ 7.6 tons 8.1 tons 7.3 tons
6 Inches Recommended New Driveway Base / RV Pad 7.41 yd³ 8.15 yd³ 11.4 tons 12.2 tons 11 tons
8 Inches Heavy Equipment Roadbed / Subbase 9.88 yd³ 10.86 yd³ 15.2 tons 16.3 tons 14.7 tons

* Tonnage estimates factor in a 10% allowance for subbase compaction and track irregularities. Standard crushed stone is calculated at 2,800 lbs/yd³ (1.4 tons/yd³); crusher run/dense grade at 3,000 lbs/yd³ (1.5 tons/yd³).

The 3-Layer Gravel Driveway Engineering Rule

Laying gravel directly on top of bare topsoil inevitably causes rutting, potholes, and sinking. Professional civil roadbuilders construct gravel driveways in three structured layers:

Layer 0

Geotextile Subgrade Fabric

Roll out heavy-duty non-woven geotextile fabric (6–8 oz) over stripped subsoil. This prevents crushed rock from sinking into the subgrade while allowing groundwater to drain freely without turning stone to mud.

Layer 1

Base Layer: #3 or #4 Ballast Stone (4"–6")

Coarse, fractured 2" to 3" rock creates an interlocking structural foundation. This layer bridges soft ground, prevents wheel rutting, and provides internal void space for subsurface stormwater runoff.

Layer 2

Middle Layer: #57 Crushed Stone (2"–3")

Angular 3/4" clean crushed limestone or granite bridges the large gaps between the ballast stones. This creates a stable intermediate transition layer that will not shift under braking or steering.

Layer 3

Surface Layer: #411 Crusher Run (2")

Also known as dense grade aggregate (DGA) or road bond. Contains 3/4" crushed rock blended with stone dust. When watered and compacted with a vibratory roller, the fines bind into a hard, cement-like surface crust. Crown the center 1/2" per foot toward side ditches.

Site Preparation Notes for 20×20 (Two-Car Gravel Parking Pad)

A 20×20 area (400 sq ft) fits two full-size passenger vehicles side-by-side. Grade the pad with a 1% to 2% crown (high center tapering toward edges) so stormwater sheds quickly instead of forming standing water puddles.

Estimated Material Cost for a 20×20 Area

4-Inch Depth (Delivered Material)
$228 – $418

Estimated material cost for 7.6 tons of #57 stone delivered by tri-axle dump truck ($30 to $55 per ton depending on distance from local quarry).

6-Inch Heavy Base (Delivered Material)
$342 – $627

Estimated material cost for 11.4 tons of structural stone delivered. If hiring a mini-excavator or skid steer operator for grading and rolling, add $600 to $1,500.

Explore Other Gravel Driveway & Pad Sizes

Frequently Asked Questions: 20×20 Gravel Area

How many tons of gravel do I need for a 20x20 area at 4 inches deep?

For a 20×20 area (400 sq ft) at a standard 4-inch depth, you need 7.6 tons of #57 crushed stone (or 8.1 tons of dense grade crusher run). This calculation factors in a 10% allowance for subbase settling and compaction. At 4 inches, the volume equals 4.94 net cubic yards (5.43 cubic yards recommended order).

How many cubic yards of gravel is a 20x20 area?

At a 4-inch depth, a 20×20 area measures exactly 4.94 net cubic yards (order 5.43 cubic yards with 10% compaction). If installing a heavy 6-inch subbase layer, you will need 7.41 net cubic yards (order 8.15 cubic yards). The formula is: (20 ft × 20 ft × [depth in inches ÷ 12]) ÷ 27.

How many dump truck loads of gravel do I need for a 20x20 project?

A standard tri-axle dump truck carries between 12 and 14 tons of crushed gravel, while a tandem-axle truck holds 7 to 8 tons. For a 4-inch depth on a 20×20 area (7.6 tons total), you will need 1 standard tri-axle dump truck load (~11.4 tons at 6"). Ordering in full truckloads significantly lowers delivery surcharges.

How much does gravel cost for a 20x20 driveway or pad?

Crushed stone (#57 limestone or granite) generally costs $30 to $55 per ton delivered. For a 4-inch depth (7.6 tons), material will cost roughly $228 to $418. For a 6-inch depth (11.4 tons), budget approximately $342 to $627 for stone delivery.