Free Imperial & Metric Updated Nov 2026

Rebar Calculator

Plan rebar for a concrete slab or footing: total linear feet, number of bars, and estimated weight. Enter the slab dimensions and your bar spacing (12 in is typical for residential, 6–8 in for driveways) and the calculator lays out a bidirectional grid with a waste allowance. Select a bar size to use its corresponding nominal weight.

Enter Dimensions

Measured to the grid boundary. Bar lengths use the same inset at each end.

Zero uses the main spacing in both directions. Enter bar centers from your plan.

Common spacing: 12 in residential, 6–8 in driveways, 6 in structural.

Standard residential is #4 (1/2 in).

Add 10% for cuts and overlaps.

Results

Total Linear Feet
242 ft
Includes waste factor — order this amount
Measurement Value Unit
Bars running across width 11
Bars running along length 11
Total Linear Meters 73.8 m
Grid Bars / Lines This is the number of straight bars/lines in the reinforcement grid. Actual stock-length purchasing depends on bar lengths, cuts, laps, bends, and project details. 22 bars
Estimated Weight Calculated using the selected rebar size 161.7 lbs
Estimated Weight 73.3 kg
Your layout

Recommended Order:  266.2  ft

Includes 10% waste allowance (10–15% typical for this material)

Simple grids: 10%. Complex layouts with many short pieces, hooks, or L-bars: 15%.

Enter Your Price
$
Estimated total $0.00

How to measureRebar Grid Diagram

Slab length Slab width Bar spacing
Rebar Grid Diagram
Measure slab length and width from above. Use center-to-center bar spacing and grid inset from your plan.
ƒ

How the Formula Works

1

Count rows (bars running along width)

Rows = ⌊Length ÷ Spacing⌋ + 1

One bar at each spacing interval plus one at the far edge

2

Count columns (bars running along length)

Columns = ⌊Width ÷ Spacing⌋ + 1
3

Calculate total linear footage

Linear ft = (Rows × Width + Columns × Length) × (1 + Waste %)

Each row spans the full width; each column spans the full length

4

Calculate weight

Weight (lbs) = Linear ft × (Weight per ft)

Weight is dynamically calculated based on selected rebar size

Frequently Asked Questions

The amount of rebar you need depends on your slab dimensions, bar spacing, chosen bar size, and waste percentage. A standard bidirectional grid requires rows and columns calculated by dividing the slab length and width by the spacing. Our calculator computes the total linear footage and estimated weight based on these factors.

For a typical concrete slab, rebar is laid out in a grid pattern. To find the exact quantity, measure the length and width of the pour and determine the required bar spacing. For example, a 10×10 ft slab with 12-inch spacing requires 22 total grid bars and 242 linear feet of rebar (including 10% waste).

The exact amount is dictated by the grid layout. First, count the number of bars running the length, and the number of bars running the width. Multiply the number of rows by the width and columns by the length, add the two together, and include a waste factor (typically 10%).

Common spacing and rebar sizes vary by project. Residential examples may use 12-inch spacing and #4 rebar, but actual reinforcement requirements depend on slab design, loads, site conditions, and applicable codes. Verify project-specific requirements with a qualified professional or local building authority.

Rebar weight is calculated by multiplying the total linear footage of the rebar grid by the specific weight per foot of the chosen rebar size. For example, standard #4 rebar weighs 0.668 pounds per foot. If you need 100 linear feet of #4 rebar, the total estimated weight is 66.8 pounds.

For a 30×40 ft slab using 16-inch spacing and 10% waste, you will need 23 rows and 31 columns, resulting in 54 total grid bars. This equates to 2,035 total linear feet of rebar. If using #4 rebar, the estimated weight would be approximately 1,359.4 lbs.

While some rough estimates use a fixed amount of rebar per square foot, it is not an accurate or safe method for purchasing material. The exact quantity needed can vary widely based on the dimensions of the slab, the required spacing, and the waste percentage. Our calculator uses the actual dimensions to provide a precise estimate.

Common spacing and rebar sizes vary by project. Residential examples may use 12-inch spacing and #4 rebar, but actual reinforcement requirements depend on slab design, loads, site conditions, and applicable codes. Verify project-specific requirements with a qualified professional or local building authority.

References

  1. American Concrete Institute ACI 318 – Building Code Requirements for Structural Concrete (Reinforcement)
  2. Concrete Reinforcing Steel Institute CRSI Design Handbook

How to Plan Rebar Grids for Concrete Slabs

Steel reinforcement controls temperature shrinkage cracking and carries tensile loads in concrete. This calculator determines the total linear footage, bar counts, and estimated steel weight for a bidirectional grid:

  1. Enter Slab Dimensions: Input the length and width of the pour in feet and inches (or meters).
  2. Select Bar Spacing: Standard residential slabs use 12-inch or 16-inch on-center (OC) grid spacing. Heavy vehicular pads or commercial foundations may specify 8-inch to 12-inch spacing.
  3. Choose Rebar Size: #4 rebar (1/2-inch diameter) is the standard for residential flatwork, while #3 is common for light patios and #5 for heavy structural foundations.

Rebar Requirements by Slab Size (Standard 12″ On-Center Grid, #4 Bar)

The reference table below displays grid lines, total linear footage (including 10% waste for lap splices), standard 20-foot stock bar quantities, and estimated steel weight:

Slab Size (ft) Area (sq ft) Grid Lines (Rows + Cols) Linear Feet (+10%) 20-ft Stock Bars Steel Weight (#4 Bar)
10′ × 10′ 100 22 lines (11 × 11) 242 ft 13 bars 162 lbs
12′ × 12′ 144 26 lines (13 × 13) 344 ft 18 bars 230 lbs
16′ × 20′ 320 38 lines (17 × 21) 762 ft 39 bars 509 lbs
20′ × 20′ 400 42 lines (21 × 21) 924 ft 47 bars 617 lbs
24′ × 24′ 576 50 lines (25 × 25) 1,320 ft 66 bars 882 lbs
30′ × 40′ (16″ OC) 1,200 54 lines (23 × 31) 2,035 ft 102 bars 1,359 lbs

Rebar Sizing: #3 vs. #4 vs. #5 Comparison

US standard rebar sizes correspond to the bar diameter in eighths of an inch:

  • #3 Rebar (3/8-inch, 0.376 lb/ft): Used primarily for residential sidewalks, decorative garden paths, swimming pool shells (shotcrete), and light masonry joint reinforcement.
  • #4 Rebar (1/2-inch, 0.668 lb/ft): The universal standard for residential flatwork including patios, driveways, garage slabs, foundation footings, and basement walls.
  • #5 Rebar (5/8-inch, 1.043 lb/ft): Specified for commercial slabs, retaining walls, suspended structural decks, and footings carrying multistory load-bearing columns.

Lap Splice Rules & Overlap Requirements

Because steel rebar is sold in fixed stock lengths (typically 20 feet), multiple bars must overlap to transfer tensile forces across joints:

  • Standard Overlap Rule: The American Concrete Institute (ACI 318) recommends a minimum contact lap splice of 30 to 40 bar diameters.
  • #4 Rebar Lap Distance: For #4 rebar (0.5-inch diameter), the minimum lap distance is 30 × 0.5 in = 15 inches (or 20 inches for critical structural tension splices).
  • Tie Wire: Tie overlaps with 16-gauge black annealed wire using a figure-eight or snap tie to prevent separation during the concrete pour.

Clearance & Rebar Chairs (Critical Placement Rule)

Rebar must be positioned in the middle to upper third of the slab depth to provide tensile resistance against top loads and temperature shrinkage. Rebar laying flat on the ground provides zero structural reinforcement and is prone to rapid moisture corrosion. Use plastic rebar chairs, concrete "dobies" (brick bolsters), or metal wire stands spaced every 3 to 4 feet to hold the steel grid securely 1.5 to 2 inches off the subgrade.