Exact Dimension Guide 100 Sq Ft Patios & Outdoor Living

How Much Concrete Do You Need for a 10×10 Slab?

Calculate the exact ready-mix yardage, 80-lb and 60-lb bag counts, subbase gravel, and rebar reinforcement needed for a 10×10 concrete slab (100 sq ft).

Instant Concrete Estimate — 10×10 Slab (100 sq ft)
Includes recommended 10% waste factor
6-Inch Thick Slab
2.04 Cubic Yards

Exact net volume: 1.85 yd³ (50 cu ft)

92 80 lb bags (+10%)
or
123 60 lb bags (+10%)

Heavy-duty application: Garage floors, carports, RV pads, hot tub foundations, machinery shops.

Ready-Mix Truck vs. Bagged Recommendation: Mixing 62 bags (80-lb) by hand takes 3–4 hours for a 2-person crew. If ordering ready-mix, expect a minimum load fee or combine with a friend’s pour.

Customize Your 10×10 Slab Calculation

The calculator below is pre-configured for a 10′ × 10′ slab. Modify thickness, waste percentage, or local price per yard to calculate exact costs in real time:

Enter Dimensions

Quick Presets:

Separate dimensions with x and entries with commas. Use positive decimal dimensions.

Enter length x width in decimal feet, separated by commas. Example: 4x5, -2x3 adds 20 ft² and deducts 6 ft². Use non-overlapping sections at the same depth.

Standard residential slabs are 4 in thick

Results

Concrete Required
1.235 yd³
Standard US ready-mix order unit

Equivalent

75 × bags 60 lb Bags (raw) Exact volume only — no waste allowance
56 × bags 80 lb Bags (raw) Exact volume only — no waste allowance
82 × bags 60 lb Bags (+ 10% waste) Recommended order quantity including 10% waste allowance
62 × bags 80 lb Bags (+ 10% waste) Recommended order quantity including 10% waste allowance
33.333 ft³ Cubic Feet
0.944 m³ Cubic Meters
Your layout

Recommended Order:  1.36  yd³

Includes 10% waste allowance (5–15% typical for this material)

Simple rectangular slabs: 5–10% is adequate. Add 15% for complex shapes or uneven subgrade.

Estimated Cost Market Rate
$123  –  $216 per cubic yard (ready-mix)

Based on current market rates. Actual cost varies by region, supplier, and project complexity.

Enter Your Price
$
Estimated total $0.00

How to measureSlab dimensions diagram

Length Width Thickness Volume = length × width × thickness
Slab dimensions diagram
Concrete slab: length × width × thickness — enter each dimension above to calculate volume.

10×10 Slab Concrete Volume & Bag Chart

Reference table comparing exact net volume and recommended order amounts across standard residential slab thicknesses for 100 square feet:

Slab Thickness Recommended For Net Cu Ft Net Cu Yds Order (Yds + 10%) 80 lb Bags (+10%) 60 lb Bags (+10%)
4 Inches Recommended Sidewalks, Patios, Light Sheds 33.33 ft³ 1.23 yd³ 1.36 yd³ 62 82
5 Inches Workshops, Carports, Light Trucks 41.67 ft³ 1.54 yd³ 1.7 yd³ 77 102
6 Inches Two-Car Garages, RVs, Hot Tubs 50 ft³ 1.85 yd³ 2.04 yd³ 92 123
8 Inches Heavy Machinery, Farm Slabs 66.67 ft³ 2.47 yd³ 2.72 yd³ 123 163

* Bag calculations assume 0.60 cu ft per 80-lb bag and 0.45 cu ft per 60-lb bag, with a 10% safety allowance for subbase compaction and forms.

Engineering & Code Specifications for a 10×10 Slab

Guidelines aligned with American Concrete Institute standard ACI 302.1R (Guide for Concrete Floor and Slab Construction) and IRC Section R506:

Subbase & Compaction

4" to 6" of #57 washed crushed gravel or crusher run compacted to 95% Standard Proctor

Rebar & Mesh Reinforcement

6×6 W1.4/W1.4 welded wire mesh elevated on rebar chairs at mid-depth (2" from bottom)

Contraction & Control Joints

Centered joint each way creating four equal 5×5 ft squares cut to 1" depth

Mix Strength & Curing

Specify 3,500 to 4,000 PSI ready-mix concrete with 5% to 7% air entrainment in cold climates. Moist cure with wet burlap or spray a curing compound (ASTM C309) for a minimum of 7 days before traffic.

Project Design Notes for 10×10 (Patio / Gazebo Pad)

A 10×10 slab (100 sq ft) is the benchmark standard for backyard grilling patios, fire pit seating areas, and gazebo pads. Pitch the surface 1/8" to 1/4" per foot (1.25" to 2.5" total across 10 ft) away from the house to ensure positive storm water drainage.

Estimated Cost for a 10×10 Concrete Slab

DIY / Ready-Mix Delivery Only
$170 – $337

Concrete material cost delivered to your jobsite ($125 to $165 per cubic yard). Excludes wooden forms, rebar, gravel subbase, and tool rental.

Turnkey Professional Installation
$600 – $1,200

Typical contractor turnkey rate ($6 to $12 per sq ft for 100 sq ft). Covers site excavation, formwork, crushed stone base, rebar grid, pour, screed, and broom finish.

Explore Other Concrete Slab Sizes

Frequently Asked Questions: 10×10 Slab

How many cubic yards of concrete do I need for a 10x10 slab at 4 inches thick?

For a 10×10 slab at 4 inches thick (100 sq ft), you need exactly 1.23 cubic yards (33.33 cubic feet) of concrete. When ordering ready-mix concrete, contractors recommend adding a 10% waste allowance for subbase irregularities and spillage, bringing your recommended order to 1.36 cubic yards. The formula is: (10 ft × 10 ft × 0.333 ft) ÷ 27 = 1.23 yd³.

How many 80 lb bags of Quikrete do I need for a 10x10 slab?

For a 4-inch thick 10×10 slab, you will need 62 eighty-pound bags of concrete (or 82 sixty-pound bags), which includes a 10% safety margin. If pouring a heavy-duty 6-inch slab, you will need 92 eighty-pound bags (or 123 sixty-pound bags). Each standard 80-lb bag yields approximately 0.60 cubic feet of mixed concrete.

Should a 10x10 slab be 4 or 6 inches thick?

Choose your slab thickness based on intended use: A 4-inch pour (1.36 yd³ with waste) is standard for pedestrian patios, walkways, and small garden sheds holding under 100 sq ft. A 5 to 6-inch pour (2.04 yd³ with waste) reinforced with #4 rebar on an aggregate subbase is strongly recommended for garage floors, carports, RV pads, hot tubs, or any application supporting vehicle axle weights per ACI 302.1R and IRC R506.

How much does a 10x10 concrete slab cost?

Ready-mix concrete delivery costs between $125 and $165 per cubic yard. For a 4-inch 10×10 slab (1.36 yd³ ordered), materials will cost approximately $170 to $224. For a 6-inch slab (2.04 yd³ ordered), ready-mix concrete runs $255 to $337. A complete turnkey installation by a concrete contractor (including grading, forms, gravel base, rebar, pour, and finishing) typically ranges from $6.00 to $12.00 per sq ft, or $600 to $1,200 total for 100 sq ft.