Free Imperial & Metric Updated Nov 2026

Mortar Calculator

Calculate the mortar needed to lay brick or block, in bags and volume. Enter the wall area or unit count and the calculator estimates mortar based on typical joint sizes. Pairs with the concrete block and brick calculators for a full masonry order.

Enter Dimensions

Length (run) of the wall.

Height of the wall.

Select your masonry unit and joint size. This determines the joint factor used to calculate mortar volume.

Only used with "Custom" selection. Mortar volume per sq ft of wall face (typically 0.01–0.08).

Enter mixed yield from the selected product data sheet; preset bag yields are unverified assumptions.

Add 15% for typical masonry work; more for complex patterns or stone.

Results

Estimated Mortar Volume
4.6 ft³
Adjusted mortar volume including waste
Measurement Value Unit
Wall Area 160 ft²
Wall Area 14.86 m²
Estimated Units Bricks, blocks, or stones (with waste) 1,242 units
Estimated Mortar Volume 0.17 yd³
Estimated Mortar Volume 0.13 m³
Illustrative Bags (net) 7 bags
Illustrative Bag Estimate Assumption-based estimate including waste; verify selected product coverage before ordering 8 bags
Your layout
Enter Your Price
$
Estimated total $0.00

How to measureMortar Diagram

Wall length Wall height Vertical joint Bed joint below unit
Mortar Diagram
Measure wall face area and account for openings. Mortar fills the bed and vertical joints between units. For a bag estimate, check product yield and bedding assumptions.
ƒ

How the Formula Works

1

Calculate wall area

Wall Area = Length × Height

Measure the face area of the wall in square feet. For openings like windows and doors, you may deduct them if they are significant — for small openings, leaving them in provides a useful safety buffer.

2

Apply joint factor

Mortar Volume (net) = Wall Area × Joint Factor

The joint factor is cubic feet of mortar per square foot of wall face. The listed factors are illustrative, not verified manufacturer consumption. Use Custom with a factor established for the actual unit dimensions, bedding and joints.

3

Apply waste factor

Adjusted Mortar = Net Mortar × (1 + Waste %)

Use 15% for standard masonry work. Increase to 20% or more for stone, irregular units, complex patterns, or when mixing by hand where spillage is more likely.

4

Calculate bags required

Bags = ⌈Adjusted Mortar ÷ Yield per Bag⌉

Preset yields are unverified assumptions. Enter the selected product mixed yield using the custom option; bag weight alone does not establish yield. Round the resulting order up to whole bags.

5

Estimate unit count

Units = ⌈Wall Area × Units per ft²⌉

Standard modular brick ≈ 6.75 bricks/ft² with 3/8″ joints. CMU 8×8×16 block ≈ 1.125 blocks/ft². The unit count includes the waste factor so you order enough material in one trip.

Frequently Asked Questions

The illustrative brick preset assumes 0.025 ft3 per square foot. Under that assumption, a 100 ft2 wall needs 2.5 ft3 net. Confirm the joint-volume factor from actual masonry dimensions and bedding before using it to order.

Illustrative arithmetic only: 100 ft2 at 0.025 ft3/ft2 gives 2.5 ft3 net. At an assumed 0.60 ft3/bag, ceiling(2.5/0.60) is 5 bags. Adding 15% gives 2.875 ft3 and still 5 bags. These assumptions require product and geometry confirmation.

Select mortar type from the project specification and the masonry/product requirements. Strength alone does not determine compatibility; this calculator does not select a suitable structural or restoration mortar.

Use the joint thickness specified for the selected masonry system. Preset thickness labels identify estimating assumptions, not permission to change the construction detail.

Follow the selected mortar product instructions for mixing water, mixing time and working time. Site-mixed mortar must follow the approved project specification; the calculator does not supply a mix design.

Standard modular brick (3-5/8″ × 2-1/4″ × 7-5/8″) lays at approximately 6.75 bricks per square foot with 3/8″ mortar joints. With 1/2″ joints the count drops slightly to about 6.55 bricks/ft².

Use your supplier price and verified product yield for an order estimate. The calculator preset does not establish a universal bag count or current material price.

Mortar is used to bond masonry units together — it fills the joints between bricks, blocks, or stones and provides structural adhesion. Grout fills cavities inside CMU cores or the gaps in tile installations. The two mixes have different proportions and are not interchangeable.

References

  1. ASTM International ASTM C270 – Standard Specification for Mortar for Unit Masonry
  2. The Masonry Society TMS 402 – Building Code Requirements for Masonry Structures