Overview

Masonry estimating involves counting modular units (bricks, CMU blocks, pavers), calculating mortar and grout volumes, and applying appropriate waste allowances for cuts and breakage. Unit dimensions are nominal — actual manufactured dimensions are 3/8 inch smaller on each face to accommodate the standard mortar joint.

These calculators implement geometric and estimating relationships. References to TMS and ASTM provide context; they do not certify the preset consumption factors, product yields or a project design.

Nominal vs. Actual Unit Dimensions

Unit TypeNominal SizeActual SizeWith 3/8" Joint
Standard CMU (8" block)8×8×16"7⅝×7⅝×15⅝"8×8×16" modular
Standard modular brick2⅔×4×8"2¼×3⅝×7⅝"2⅔×4×8" modular
Queen brick2¾×4×8"2⅜×3⅝×7⅝"Queen coursing
Paver brick (standard)4×8×2.25"3⅝×7⅝×2¼"Typically dry-set

Pavers installed with sand setting bed use nominal dimensions with 1/16" to 1/8" joint spacing — far smaller than mortared masonry. Our paver calculators use the nominal face dimensions to compute coverage.

Core Formulas

CMU / Brick Count

Units = (Wall area / Unit face area) × (1 + Waste)

Unit face area includes the mortar joint: for a standard 8×16" CMU with 3/8" joint → face area = 8/12 × 16/12 = 0.889 ft² → ~1.125 units/ft².

Standard Rules of Thumb (Brick)

  • Modular brick (4" wythe): ~6.75 bricks per ft² of wall face
  • Engineer modular: ~5.63 bricks/ft²
  • Jumbo: ~5.14 bricks/ft²
  • King: ~4.89 bricks/ft²

Values per Brick Industry Association (BIA) Technical Notes 10.

Mortar Volume

Mortar (ft³) = Units × Joint volume per unit

Joint volume must be established from actual masonry dimensions, joint thickness and bedding method. The calculator presets are unverified estimating assumptions, not universal per-brick or per-block requirements. Keep waste separate when comparing estimates.

Mortar Yield from Bag

Bags = Total mortar volume / Yield per bag

Use the selected product technical data sheet for mixed yield or coverage, bag mass, water addition and masonry geometry. No universal mortar yield is verified here. For example, QUIKRETE 1102 lists up to 13 standard blocks per 80 lb bag; that product-specific coverage is not a universal default or a mixed-volume yield. The Concrete Block Calculator now requires user-supplied coverage or mixed yield plus verified mortar consumption per block; its block count is independent. Tile grout and CMU core grout require separate product specifications.

Grout Volume (Filled CMU Cells)

Grout (yd³) = (Cell area × Cell height × Cell count) / 27

Standard 8" CMU open cell: approximately 0.258 ft³ per cell void. Fully grouted: ~0.258 × number of courses × number of cells per course.

Waste Factors

MaterialDefault WasteRationale
Brick (standard wall)5%Corner cuts, window openings, breakage
Brick (complex / arch)10–15%High cut frequency
CMU block5%Openings, corner cuts
Mortar25%Bed over-fill, dropped mortar, joint tooling
Grout10%Voids, pump loss, cleanouts
Pavers (rectangular)5–7%Edge cuts, pattern borders
Pavers (diagonal/herringbone)10–15%Increased perimeter cut frequency

Mortar Mix Proportions

Mortar TypePortland CementMasonry CementHydrated LimeSandUse
Type M1—¼3–3.75Below grade, foundations
Type S1—½4–4.5General above grade, exterior
Type N1—15–6Interior, non-load bearing
Type O1—28–9Interior, very low load

Select mortar type and mix requirements from the approved project specification and the selected masonry product instructions. This methodology does not prescribe a mortar type by location alone.

Industry Standards & Code References

  • TMS 402/602-22 — Building Code Requirements and Specification for Masonry Structures (The Masonry Society). Governing standard for structural masonry design.
  • ASTM C90 — Standard Specification for Loadbearing Concrete Masonry Units.
  • ASTM C270 — Standard Specification for Mortar for Unit Masonry. Defines Types M, S, N, O.
  • ASTM C476 — Standard Specification for Grout for Masonry.
  • BIA Technical Notes 10 — Bricklaying estimating guide, Brick Industry Association.
  • IRC R606 — General Masonry Construction. Bond pattern, joint reinforcement, and attachment to framing.
  • IRC R607 — Unit Masonry, Mortar, and Grout requirements.

Limitations

  • Structural masonry design (wall thickness, reinforcement, seismic reinforcing) requires TMS 402 analysis by a licensed structural engineer.
  • Cavity wall construction, veneer anchoring, and flashing details are not modeled — allow for additional materials in detailed estimates.
  • Efflorescence, moisture barriers, and waterproofing materials are project-specific and excluded from these calculators.

References & Citations

  • The Masonry Society. TMS 402/602-22: Building Code Requirements and Specification for Masonry Structures. Longmont, CO: TMS, 2022.
  • ASTM International. ASTM C90: Standard Specification for Loadbearing Concrete Masonry Units.
  • ASTM International. ASTM C270: Standard Specification for Mortar for Unit Masonry.
  • ASTM International. ASTM C476: Standard Specification for Grout for Masonry.
  • Brick Industry Association. Technical Notes on Brick Construction, No. 10: Dimensioning and Estimating Brick Masonry. BIA, 2006.
  • International Code Council. International Residential Code (IRC) 2021. Sections R606–R608.
  • National Concrete Masonry Association. TEK 3-6C: Concrete Masonry Unit Dimensions. NCMA, 2012.

Related Calculators