Free Imperial & Metric Updated Nov 2026

Stud Calculator

Count the studs for a framed wall, including corners and openings. Enter the wall length and your stud spacing (16 or 24 in on center) to get field studs plus the extras for corners and each door or window. Built to match how walls are actually framed on site.

Enter Dimensions

Quick Presets:

Enter distance from wall start x opening width for each opening, in order. These positions replace the opening count and width. Height is shared.

Standard ceiling heights: 8 ft, 9 ft, 10 ft.

Use spacing from approved framing plans; this estimator does not design walls.

Windows and doors each count as one opening.

Rough opening width. Use average if openings vary.

Record the opening height for your cut list. This piece-count estimate uses opening width and spacing.

Results

Estimated framing pieces
20 pieces
Includes four extra end/corner pieces per wall. Short opening pieces are counted individually; use your cut list to determine full-length stock.
Measurement Value Unit
Field Studs Studs at regular OC spacing along the wall 8 studs
End/corner allowance 3-stud corner assembly at each end (4 total) 4 studs
Opening pieces (including short cuts) King studs, jack studs, and cripples for all openings 8 pieces
Wall Area Gross wall face area 108 ft²
Wall Area 10.03 m²
Your layout
Enter Your Price
$
Estimated total $0.00

How to measureWall Framing Diagram

Opening Wall length Wall height Stud spacing
Wall Framing Diagram
Measure wall length and stud spacing center to center. Locate openings from the same wall end. Use the framing plan for the assemblies around openings.
ƒ

How the Formula Works

1

Calculate field studs

Field studs = ⌊Wall length ÷ Spacing⌋ + 1

One stud at each spacing interval plus one at the far end. Each opening removes ⌊opening width ÷ spacing⌋ field studs from this count.

2

Add corner stud assembly

Corner studs = 4

Standard 3-stud corner: 2 king studs at each end plus the shared corner stud. This adds 4 studs beyond the field count.

3

Calculate opening framing per opening

Opening studs = 2 king + 2 jack + (⌈opening width ÷ spacing⌉ + 1) cripples

Each opening requires 2 king studs, 2 jack/trimmer studs, and cripple studs above the header filling the space to the top plate.

4

Scale to all openings

Total opening framing = Opening studs per opening × Number of openings
5

Sum all stud types

Total studs = Field studs + Corner studs + Total opening framing

Add 10–15% waste for cuts and miscuts on complex walls

Stud Requirements by Wall Length and Spacing

Current estimator convention: floor(length/spacing)+1 field studs, no openings, plus 4 corner studs. Order includes 10% extra. This is not a placement plan; non-divisible end spans need layout review and plates are excluded:

Wall Length16" OC Field Studs16" OC Recommended Order24" OC Field Studs24" OC Recommended Order
8 ft713510
10 ft814611
12 ft1016713
16 ft1319915
20 ft16221117
24 ft19261319
40 ft31392128

Frequently Asked Questions

A 12-foot wall at 16" OC needs ⌊144 ÷ 16⌋ + 1 = 10 field studs, plus 4 corner studs = 14 studs for a wall with no openings. Add a standard door opening (3 ft rough): subtract 2 field studs displaced, add 2 king + 2 jack + 3 cripples = 7 opening studs. Total: 14 − 2 + 7 = 19 studs. This is the estimator convention, not a placement plan: floor(length/spacing)+1 can omit an end stud on a non-divisible span. Opening and corner allowances require layout review.

Select stud spacing from the approved framing specification, including loads, wall height, lumber grade and sheathing requirements. The available spacings are estimating options, not approval for a particular wall.

King studs run full height from bottom plate to top plate on each side of an opening. Jack studs (also called trimmer studs) sit inside the king studs and support the header over the opening — they are shorter, cut to header height. Cripple studs fill the space between the header and the top plate, maintaining the OC spacing across the opening. All three types are counted in the Opening Framing output.

The estimator adds four corner studs per wall as an allowance. Actual corner and backing details can require a different count; use the framing plan and do not treat this allowance as an assembly design.

Plate count and connection details must follow the approved framing plan and applicable building requirements. Plates are excluded from this stud estimator.

Add 10% for straightforward rectangular walls. Increase to 15% for walls with many corners, angled sections, or complex header situations. Miscuts, split lumber, and last-minute adjustments are common — running short of studs mid-frame is a project delay. Leftover studs are easily used elsewhere or returned to most lumber yards.

Determine stud cut length from the specified wall assembly, plate thicknesses and finishes. A 104-5/8-inch stud plus 4-1/2 inches of plates totals 109-1/8 inches, not exactly 108 inches. Verify supplier precut dimensions against the plans.

Run this calculator once per wall, then add the totals. Shared corners between intersecting walls may let you reduce the count slightly — one wall's end studs can serve as the corner assembly for the adjacent wall. In practice, most framers calculate each wall independently and add 10% overall, since lumber is inexpensive relative to labour and a separate trip for a few extra studs costs far more than the boards themselves.

References

  1. International Residential Code IRC R602 – Wood Wall Framing
  2. American Wood Council (AWC) Wood Frame Construction Manual (WFCM)