Concrete Footing Size Chart: How Big Should Your Footings Be?

Footing size requirements for decks, sheds, walls, and foundations. Charts, formulas, and code references for residential construction.

Sizing tables need project-specific verification. The dimensional examples below estimate material only. The listed footing diameters and soil values have not been verified for your loads, soil, adopted code, or jurisdiction and must not be used as approved structural sizes. Obtain the footing and support schedule from your approved plans. The AWC deck guide explains why the framing layout and tributary loads matter.

Footing size is one of the most commonly underspecified elements in residential construction. Under-sized footings settle, tip, or fail — causing damage that’s extremely expensive to repair. This guide covers how to size footings correctly for common residential applications.

Quick Answer: Footing area = Load ÷ Soil bearing capacity. For residential work, use the allowable bearing pressure established for the site. Always extend below your local frost line — the most common and most expensive footing mistake is going too shallow.

What Is a Footing?

A footing is a widened concrete base that spreads a structural load over a larger soil area. The purpose: reduce the pressure on the soil below the bearing capacity of that soil.

Without a footing, a post carrying 5,000 pounds concentrated in a 4×4 area would exert far more pressure per square inch than most soils can support. The footing spreads that load over a larger area.

The Core Sizing Principle

Footing Area = Load ÷ Soil Bearing Capacity

Soil bearing capacity for common soil types:

  • Clay (soft): 1,000–2,000 psf
  • Clay (medium): 2,000–4,000 psf
  • Sand (loose): 2,000–3,000 psf
  • Sand (dense): 3,000–6,000 psf
  • Gravel: 4,000–8,000 psf
  • Bedrock: 10,000+ psf

If you don’t know your soil type, obtain a site-specific allowable bearing value; 1,500 psf is not a guaranteed safe default.

Deck Footing Sizes

Deck footings support specific posts that carry tributary areas of the deck. IRC table R507.3.1 provides footing diameter requirements based on load area and soil capacity.

Deck Post Footing Diameter (Round Footings)

Use the footing schedule from approved plans. Required inputs include tributary loads, framing layout, site bearing pressure and the applicable code. This article does not provide a verified diameter-selection table.

Tributary area is the deck area carried by a support; dividing total area equally among posts is not valid for every framing layout.

Use our Deck Footing Calculator to calculate concrete volume per footing.

Foundation Wall Footing Sizes

Obtain footing width, thickness and reinforcement from the approved foundation schedule. Story count alone does not establish these dimensions. No universal IRC minimum-size table is provided here.

Footing Depth: The Frost Line

Use the approved founding depth and frost-protection detail. Regional depth estimates do not replace site-specific requirements.

Approximate frost depths:

  • Deep South (FL, south TX, AZ): 0–12 inches
  • Southeast (NC, TN, GA): 12–18 inches
  • Mid-Atlantic: 24–36 inches
  • Great Lakes: 36–48 inches
  • Upper Midwest (MN, ND): 42–60 inches
  • Northern New England: 48–72 inches

Check your specific frost depth with your local building department — this is the single most common footing error.

Concrete Volume for Footings

Strip Footings

Volume = Length × Width × Depth

For a 60-foot perimeter house, 16” wide × 8” deep footing:

  • 60 × (16/12) × (8/12) = 53.3 cubic feet = 1.97 cubic yards

Round Column Footings

Volume = π × r² × Depth

For a 12” diameter, 42” deep footing:

  • π × (0.5)² × 3.5 = 2.75 cubic feet ≈ 5 bags of 80 lb concrete

Use our Concrete Footing Calculator for all footing configurations.

Frequently Asked Questions

Do I need rebar in residential footings? Use the approved reinforcement schedule for bar size, count, spacing, cover, anchorage and splices. This material estimator does not establish reinforcement requirements.

What’s the minimum footing size for a fence post? Use the approved fence/post specification and local requirements for wind, soil and embedment. This page does not establish a universal minimum hole diameter or depth.

Can I pour a footing in cold weather? Use the concrete supplier and approved cold-weather placement and curing plan. Do not select additives, placement temperature or protection duration from a generic rule.

What happens if my footing is too shallow? Frost heave lifts the footing, which can crack the foundation, rack door and window frames, and damage finishes. The cost of properly deep footings is trivial compared to the cost of fixing frost heave damage.


See also: Concrete Calculation Methodology — footing volume formulas, bag yield tables, and IRC R403.1 references. Also see the Frost Depth Reference for all 50 states.

BuildByMath Team

Construction estimator and technical writer at BuildByMath. Focused on material calculations for residential and light commercial projects.